18成禁人10000视频免费,中文字幕熟妇人妻在线视频,久久久综合精品一区二区三区,亚洲欧美日本

網站首頁技術中心 > CD-800 Dicing Machine               Instruction
產品目錄
CD-800 Dicing Machine               Instruction
更新時間:2013-07-29 點擊量:3693

This type of machine is specialized in vegetable and cormcutting. It is easily operating for woman. It is also the necessary facility for restaurants and second processing factories. Instantaneous ability is above 15 people. This machine will let you have satisfied feeling.

 

A.   Processing material

    Potatoes, carrots, melons, bamboos, onions, apples, vegetables and so on.

 

B. Processing dimension:

(standard)

               H                 10. 15. 20mm cubes or bars.

L              T            (special dimension)

                             3-20mm cubes or bars.

 

C. Capacity

15/mm cubes;    1000kg/hr

 

D.   Voltage

3 phase / 415V, 50Hz / 4P / 0.75KW

(each countries has different voltage connection)

E.   Machine dimension & weight

L 800×W 700×H 1260mm

 

F. Cutting work outline

    Connecting “ON” switch, add little water when machine is running and put suitable amount of material to the machine. (Material diameter under 8/cm). Leaf blade will turn over the material to the fixed thickness of the place of flate cutter. And crosscut cutter will cut the bars into cubes and flow down to the machine after round cutter cuts material into bars. Easily operate, and processing material is clean and delicacy.

 

 

 

 

 

 

 

 

 

 

 

G. Voltage connection

    Power: 3 phase / 415V / 4P / 0.75KW. Connect power cord (red, black, white) when use the machine. Then connect (green) line to insurance after that start to operating.

 B

 

 

 

 

 

               A

 

(1) The power line A connected to power supply. (Attention the    motor shift)

(Attention 4 power lines, green for the grounding line.)

(2) Water pipeline will be connected B, then the installation is completed.

 

 

 

H.   Installing location

    Consider whether the water drains unimpededly or not when install the machine.

 

I.   Watch out the machine running

    Make sure there are no foreign objects on the entrance of the machine and inside of the leaf blade after connecting voltage to avoid the cutter broken while the machine running. Make sure the direction of leaf blade is correct, rith circum gyratoin (clock-wise).

 

J. Method of adjusting thickness of flate cutting

The standard allocation method as follows: (if cut cube is formed by three Cutter)

(1) The first knife (cutting thickness): Plane broadswords Z.     (Adjustable by cutting thickness)

(2)   The second knife (cutting width): Circular knife Group Y.

  5mmP (space): 5mm

 10mmP (space): 10mm

 15mmP (space): 15mm

 20mmP (space): 20mm

 

(3)   The third knife (cut length): transverse plane knife Group.

5mm uses 15 knife group

10mm uses 8 knife group

15mm uses 6 knife group

20mm uses 4 knife group

 

K.   Method of adjusting aluminum fence

Aluminum fence feeds material to crosscut cutter when round cutter cuts the material. This is why the sharp place of aluminum fence has to get close to the cushion of gap of round cutter or the dimension of aluminum fence marks on the bottom right side.

 

L. Round cutter discharging

Round cutter dimension drawing

Round cutter dimension

 

 

Standard (mm)

P: 10

P: 15

P: 20

Special (mm)

P: 3-20

(1) Avert black screw of fixed eccentric axis.

(2) Pull down the fixed bolt of round cutter eccentric axis. Then round cutter can be discharged.

(3) Fix the u-shape spanner on the round cutter set, then loosen sexangular on the round cutter axis (two sides of 24m/m spanner), then it can be taken out.

 

 

 

M. Crosscut cutter discharge

Crosscut cubes round piece

5m/m uses 21 pieces

10m/m uses 8 pieces

15m/m uses 6 pieces

20m/m uses 4 pieces

(1) Fix u-shape spanner on the fixed crosscut cutter set when discharge crosscut cutter. Then loosen sexangular screw (24m/m spanner), then it can be taken out.

 

N. Daily cleansing

    Clean the machine after finish the jobs. Run the machine while operating, then wash it by flush water to clean the leavings.

O.   Standard by-products:

Spanner         10, 19, 24………….3

Screwdriver (-), (+)……….……………2

U-shape spanner                 1 PCS

Lubricant oil                    1

Tool box                       1 box

精品欧美一区二区三区成人片在线| 99精品视频一区在线观看| 97亚洲狠狠色综合久久久久| 国产三级在线观看完整版| 色欲av精品一区二区三区| 一本色道久久综合狠狠躁篇| 久久精品人妻少妇一区二区三区| 免费啪啪a片aaaa片老太婆交| 成人免费一区二区三区视频| 久久精品亚洲AV中文2区金莲| 国产古装又黄A片在线观看| 草草久久久亚洲av成人片| 特黄a级毛片免费视频| 久久精品国产亚洲AV麻豆蜜芽 | 批日出水免费观看40分钟| 国产A级毛片久久久久久精品 | 花蝴蝶日本视频免费高清| 欧美性色欧美a在线在线播放| 真人性做爰无遮a片免费| 久久久国产精品消防器材| 久久久无码精品国产一区 | 裸身美女无遮挡永久免费视频| 国产精品无码一本二本三本色| 秋霞国产成人精品午夜视频APP| 精品国模一区二区三区| 色婷婷亚洲一区二区三区| 爆乳熟妇一区二区三区| 久久熟妇人妻午夜寂寞影院| 美妙人妻系列| 国内精品伊人久久久久AV| 国产激情久久久久久熟女老人| 被夫上司玩弄的人妻| 久久久精品午夜免费不卡| 免费观看性欧美大片无片| AV人摸人人人澡人人超碰小说| 无码高潮少妇毛多水多水免费| 免费高清视频免费观看| 乱人伦人妻精品一区二区| 最近韩国日本免费观看免费| 好吊视频一区二区三区| 伊人久久丁香色婷婷啪啪|